Instruhub

Product Highlights

The TS22 Series telephone test equipment offers a combination of reliability, durability and expanded utility.

• TS22 Test Set has an amplified speaker for hands-free monitoring
• TS22A Test Set has a two-way speakerphone for true hands-free conversation
• DropSafe^TM reliability passes 20-foot drop test
• RainSafe^TM protection in severe weather conditions
• Stores nine 18-digit numbers in repertory dialer (speed dialing)

Overview

The TS22 Test Set’s unique built-in one-way amplified speaker provides three audio levels for hands-free listening and use with automated voice response systems. Multiple memories enable storage of nine 18 digit telephone numbers in repertory dialer (speed dialing) for easy access to test boards, the central office and other frequently called numbers. The last number redial feature eliminates the need to re-key your last entry. The TS22 Test Set offers an unbeatable combination of reliability, durability and expanded utility.

* The TS22 Series Test Set contains an embedded 3-volt lithium battery.  The 9-volt battery in the Test Set should be changed when low, or once a year if not in use, to prevent the 3-volt battery from draining.  A 3-volt battery that drains after its 42-month warranty will need to be replaced by an authorized service facility at a charge to you.

* Note also that your speakerphone will no longer work when your 9-volt battery is low or dead.  You should replace the 9-volt battery whenever it is low.

Features Combining reliability, durability and expanded utility

The TS®22 Series Test Sets top features include:

• Tone (DTMF) and pulse operation
• Last number redial
• DTMF signal levels compensated for loop length
• DropSafe™ unit up to 20 feet
• Audible electronic ringer
• Locking mute switch
• 3-year redial storage time
• Over voltage and over current protection
• PBX pause button
• Field replaceable belt clip
• Continuous polarity LED indications
• For use with computerized voice response systems
• Stores nine 18-digit numbers in repertory dialer (speed dialing)
• RainSafe™ ruggedness for use in extreme weather conditions
• TS22A includes above and additionally high impedance monitor for DataSafe™ operation and two-way speakerphone

Specifications Electrical

Electrical

Loop Limit

2 kΩ maximum at 48 VDC (nominal 20 mA minimum loop current)

DC Resistance
(Talk Mode)

300 Ω typical

Monitor Impedance

Monitor Impedance

TS22

5 kΩ nominal at 1 kHz

TS22A

120 kΩ nominal at 1 kHz

Rotary Dial Output

Rotary Dial Output

Pulsing Rate

10 pps ±5 pps

Percent Break

61 % ± 2 %

Interdigit Interval

1000 ms typical

Leakage During Break

>50 kΩ

Physical

Physical

Physical Measurement

10.25 in x 2.69 in x 3.38 in (26 cm x 6.83 cm x 8.57 cm)

Weight

Weight

TS22

21 ounces (.595 kg)

TS22A

22 ounces (.624 kg) typical

Environmental

Environmental

Temperature Operating:

29 °F to 140 °F (-34 °C to 60 °C)

Storage

-40 °F to 150 °F (-40°C to 66 °C)

Altitude

To 10,000 feet (3,000 meters)

Relative Humidity

5 % to 95 %

Product Highlights

The TS30 features the latest in telephone test set case design, at an affordable price.

• High impedance DataSafe^TM operation in monitor mode
• DropSafe^TM reliability passes 20-foot drop test
• RainSafe^TM protection in severe weather conditions
• Mute switch
• Last number redial
• Audible ringer for callbacks

Overview

Recognized as the industry standard for basic test sets, the TS30 Test Set provides superior quality at an affordable price. With its high impedance Monitor for DataSafe™ operation, technicians can clip onto a line in Monitor mode without disrupting existing traffic.

Features Rugged butt-in telephone test set at an affordable price

The TS®30 Test Set top features include:

•  High impedance monitor mode
• Automatic regulation of speech levels
• Tone and pulse operation
• Last number redial in tone and pulse modes
• RainSafe™ weather protection for use in extreme weather conditions
• Hook flash button
• Fully functional with either line polarity
• Audible electronic ringer for call backs
• High current and over voltage protection
• High impact polycarbonate case
• Field replaceable spring-loaded belt clip
• Hearing aid compatible receiver
• Transmitter Mute switch
• Talk and Monitor modes
• Ergonomic design
• Lightweight unit is easily transported

 Models & Accessories

Models

30800001 30800009 12001005 Specifications Electrical

Electrical

Return Loss

>14 dB (ref 600 Ω)

Line Current Range

15 mA to 120 mA

Resistance to Continuous Current (Talk Mode)

275 Ω typical at 20 mA

Monitor Mode Impedance

>120,000 Ω 300 Hz to 3400 Hz

Pulse Dial Output

Pulse Dial Output

Pulsing Rate

10 pps pps

Open/Close Ratio

60/40

Inter-digit Interval

800 ms %, -10%

Resistance During Pulse Open

> 200,000 Ω

Protection Against Alternating Current Overvoltage

The TS30 survives up to 250 Vrms across its test leads.

Peak Acoustic Output of the Receiver

<120 dBspl

DTMF Output Tone Frequencies Tone Frequency Error

per ITU-T Q.23 ±1.5% Maximum

Tone Level

Tone Level

High Group Low Group

-4 dBm (into 600 Ω) -6 dBm (into 600 Ω)

High vs Low Tone Difference

2dB +1db

Last Number Redial (Tone/Pulse)

Last Number Redial (Tone/Pulse)

Memory Capacity Memory Retention

23 digits 8-minutes nominal

Flash Duration

600 ms ±100 ms

Ringer Loudness

> 70 dBA at 1 meter

Ringer Equivalent (REN)

0.14

Measurements

10 in x 2.83 in x 3.34 in (25.5 cm x 7.2 cm x 8.5 cm)

Weight

16.8 ounces (0.476 kg)

Environmental

Environmental

Temperature Operating Storage

-4 °F to +140 °F (-20°C to +60°C)
-40 °F to +151 °F (-40°C to +66°C)

Relative Humidity

5% to 95%

Safety

Safety

Telecom Electrical

TNV-3

Safety Classification

IP54

Regulatory Standards Used

Regulatory Standards Used

Certifications and Compliance

Certifications and Compliance

Product Highlights

• Caller-ID and Call Waiting Caller-ID
• Amplified speakers for hands-free monitoring
• Data lockout and data lockout override
• Tone generator for wire identification
• Talk battery to power voice conversation on dry (non-powered) lines
• Easy to read oversized liquid crystal display

Overview

This feature-rich test set is a necessity for a variety of installs. The TS25D Test Set features data lockout and lockout override, making you completely safe in talk or monitor mode. The DSL/POTS filtering technology allows you to safely draw dial tone without downing DSL.

Features Features data lockout, lockout override and a large LCD 

The TS®25D Test Set top features include:

• Caller ID and call-waiting caller-ID (on N. American phone systems)
• Data lockout and data lockout override
• DSL/POTS filtering technology lets you safely draw dial tone from a pair that is carrying voice and ADSL without downing the ADSL service
• Built-in analog tone generator for tracing and identifying wires with a probe
• DTMF digit grabbing capability
• Talk battery to supply power to non-powered (dry) pairs to carry voice conversation
• Row/column tones for single tone dialing
• High voltage Lockout/Low voltage Lockout
• Continual data detection in monitor mode
• Over voltage and over current protection
• Amplified speaker for hands-free monitoring
• Programmable phonebook stored in non-volatile memory
• Speed dial (10 memories, 23 digits each)
• Selectable flash and pause duration
• Battery level indicator
• Battery included

Models & Accessories

Models

25501004 25501009  25501109

Accessories

25500100 25500300 25500400

 

Specifications Electrical

Electrical

Return Loss

>14 dB (ref 600 Ω)

DC Resistance

DC Resistance

Off-Hook

150 Ω nominal

On-Hook

>1 MΩ

AC Impedance

AC Impedance

Off-Hook

600 Ω nominal; 300 Hz to 3400 Hz

On-Hook

>120 kΩ; 300 Hz to 3400 Hz

Rotary Dial Output

Rotary Dial Output

Pulsing Rate

10 pps ±1 pps

Break/Make Ratio

60/40

Interdigit Interval

>300 ms

Resistance During Break

>100 kΩ

DTMF Output

DTMF Output

Tone Frequency Error

±1.5 % maximum

Tone Level

–1 dBm combined (typical)

High versus Low Tone difference

2 dB ± 2 dB

Memory Dialing

Memory Dialing

Memory Capacity

10 speed dial memories plus one last number redial memory

Digit Capacity

23 digits per memory

Pause Duration

User programmable Default: 4 seconds

Hook Flash Duration

User programmable Default: 600 ms

Automatic Speaker Shut Off Duration

User programmable TS25D default: 5 minutes TS25D CO default: 2 minutes

Battery

9 V alkaline or lithium battery

Physical

Physical

Measurement

7.8 in x 2.7 in x 1.6 in (20 cm x 6.8 cm x 4 cm)

Weight

10 ounces (284 g)

Environmental

Environmental

Temperature Range Operating

32°F to 122 °F (0 °C to 50 °C)

Storage

-40 °F to 150 °F (-40 °C to 65 °C)

Altitude

Up to 10,000 ft (3,000 m)

Relative Humidity

5 % to 95 %

Product Highlights

A three-in-one—TDR, toner and pair identifier—premium, VDV telephone test set..

Ten testing functions include:

• TDR – find cable length measurement and locate faults on virtually all types of cable including twisted pair, coaxial, and parallel conductors
• Toner – five separate tones for fast and easy differentiation between multiple wire pairs
• SmartTone® – short the correct pair and tone changes for exact pair identification
• Data indication – warns when data is present on the line
• Voltage indication/measurement – identifies potential line problems

• Current (mA) indication/measurement – verifies sufficient line current
• Caller-ID with Call Waiting CID – verifies functional service
• DTMF Digit Grabbing – isolates faulty customer premise equipment
• Detects dial tone, places and receives calls
• Polarity

Overview

Fluke Networks’ new TS52 PRO Test Set features the latest in test set technology. Designed with a superior, radiant liquid crystal display (LCD) user interface, it allows you to see what cannot be heard in any outside plant environment.

Models & Accessories

Models

TS54-A-09-TDR TS54-BANA Specifications Electrical

Electrical

Current range (Off-hook)

10 mA to 100 mA

DC Resistance

DC Resistance

Off-hook

150 Ω nominal

On-hook

>3 M Ω

AC Impedance

AC Impedance

Off-hook

600 Ω nominal; 300 Hz to 3400 Hz

On-hook

>120 kΩ 300 Hz to 3400 Hz

Headset impedance

32 Ω

Rotary Dial Output

Rotary Dial Output

Pulsing Rate

10 pps ±1 pps

Break/make ratio

60/40

Interdigit interval

>300 ms

Resistance during break

>100 kΩ

DTMF Output

DTMF Output

Tone frequency error

±1.5 % maximum

Tone Level

-3 dBm combined (typical)

High versus low tone difference

2 dB ± 2 dB

Speed Dialing

Speed Dialing

Memory capacity

9 speed dial memoriesof 23 digits, plus one last number redial memory

PBX pause duration

User programmable; default of 4 seconds

Hook flash duration

User programmable; default of 500 ms

Automatic shut-off duration

User programmable; default of 2 minutes

Voltage measurement

Voltage measurement

Range

4 V dc to 140 V dc

Current measurement

Current measurement

Range

0 mA to 100 mA

TDR

TDR

Range

3,000 feet (914 m)

Accuracy

±2 m ±5 %

SmartTone toner

SmartTone toner

Frequencies

Steady tone: 950 Hz

Power

Power

Battery type

9 V alkaline battery

Physical

Physical

Measurement

8.3 in x 3.2 in x 2.6 in (211 mm x 81 mm x 66 mm) (without belt)

Weight

1.16 lb (0.53 kg) (without belt clip)

Water resistance

The test set is rain and moisture resistant and IP64 rated

Environmental Temperature Range

Environmental Temperature Range

Handset speech and dialing functions

-22°F to 140 °F (-30°C to 60°C)

LCD function

-13°F to 140°F (-25°C to 60°C)

Storage

-22°F to 150°F (-30°C to 66°C)

Altitude

To 10,000 ft. (3,000 m) max

Relative Humidity

95% to 30°C
75% to 40°C
45% to 50°C

Primary Current Injection Kit  MOTWANE

 Importers Distributors,Dealers of MOTWANE suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

 

The MOTWANE made primary current injection MOT-PIK series is the most reliable & effective kit for testing & commissioning of protection system in electrical substation. The PIK series offer high output current upto 3000 Amps with relatively high burden up to 20kVA. It is designed with user friendly features to check operations of protection component system including Current transformer, Circuit Breaker, current sensor & relays etc. 

 

The MOTWANE made primary current injection MOT-PIK series is the most reliable & effective kit for testing & commissioning of protection system in electrical substation. The PIK series offer high output current upto 3000 Amps with relatively high burden up to 20kVA. It is designed with user friendly features to check operations of protection component system including Current transformer, Circuit Breaker, current sensor & relays etc. The Motwane PIK with high VA burden makes it possible to deliver desired current to high impedance object like Current transformer. It has optional feature to measure CT secondary current as well as polarity.

Features 

• Variable output current 
• High VA burden to test high impedance objects 
• Digital timer for measuring tripping time
• Zero start interlock for safety
• Auto cutoff upon tripping relay 
• Current range ( Low – 50% & High – 100% of full range ) 
• CT sec current measurement
• CT polarity detection
• Wheel mounted for easy transportation

 

Application

The primary current injection method is usually the preferred method to verify the current sensors, wiring, and the current conduction path in the breaker. In order to identify sensor and wiring-related problems, it is recommended that the primary current injection test be conducted separately on each phase through current transformer which ensures that the sensors and wiring of the breaker are working proper.

 

The Primary current injection method is also useful for testing current transformer ratio. The secondary current of the transformer bears a known relationship with the primary current. Any change in the primary current is reflected in the secondary circuit. To verify the turns ratio and polarity tests on CT, current is injected on primary side of CT and measured at the secondary side for relaying and to ensure that they have the correct turn’s ratio and relaying accuracy.

 

High current injection (Primary current) is used and recommended during commissioning of protection systems. It is also recommended during major repairs and component replacement in power substations.

 

Motwane makes Primary Current Injection Kits are used to test Current Transformers, Circuit Breakers, Bus Bars, Relays, MCBs, MCCBs etc. 

 

SPECIFICATIONS

 

Model MOT-PIK200 MOT-PIK500 MOT-PIK800 MOT-PIK1000 MOT-PIK1500 MOT-PIK2000 MOT-PIK2500 MOT-PIK3000

Output current 0-200A 0-500A 0-800A 0-1000A 0-1500A 0-2000A 0-2500A 0-3000A

O/P Accuracy ±1.5% of full scale reading ± 2 digits

O/P Resolution 1A

OCV @ full Voltage 5V 6V 6.25V 5V 7V 7V 6V 6.67V