Instruhub

Sensitivity	1 mV/ms^-2
Operating Temperature Range	-55 to +125 deg C
Maximum Operational Level (peak)	500 G
Freq. range	1 - 25000 Hz
Weight	2.9 G
Residual Noise Level in Spec Freq Range (rms) +-	2500

Minimum order quantity: 1 Piece

MINIATURE ACCELEROMETER, DELTATRON, CCLD  B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore Miniature accelerometer Type 4397 is designed for measurements on lightweight structures where relatively high-level, high-frequency vibrations are encountered. Delivered with cable included.

Miniature accelerometer with internal electronics CCLD is well-suited for measurements on lightweight structures where relatively high-level, high-frequency vibrations are encountered. Type 4397A uses a M3 connector.

USE SCENARIOS

• Shock and vibration measurement
• Vibration analysis
• Vibration monitoring
• Vibration test control
• Product and quality control

The accelerometer require an external constant-current power supply and operate as voltage sources. Output signals come in the form of voltage modulation on the power supply line.

ACCELROMETER FEATURES

Type 4397 is a DeltaTron accelerometer; this means it operates on constant-current line-drive (CCLD) ICP® principles, and features:

– Integral preamplifiers
– All-welded construction (withstands rough environment)
– Delta Shear Uni-Gain® design
– Low sensitivity to all environments
– Individual standard-traceable calibration
– Individual data for best fit to measured frequency response

The DeltaTron name identifies products that operate with a constant-current power supply and give output signals in the form of voltage modulation on the power supply line. 

Accelerometers, like Type 4397-A, are constructed to the proven Brüel & Kjær Delta Shear design with the addition of an integral DeltaTron preamplifier.

Operating Temperature Range	-55 to +125 deg C
Freq. range	0.3 - 2000 Hz
Weight	18G
Maximum Operational Level (peak)	14G
Connector	4-pin

Minimum order quantity: 1 Piece

MINIATURE TRIAXIAL CCLD ACCELEROMETER BKSV.COM Type 4506-B-003 Miniature Triaxial Piezoelectric CCLD Accelerometer (500Mv/G) with TEDS, is designed for structural analysis within the automotive industry. Supplied excl. cable

A combination of high sensitivity, low mass and small dimensions make Types 4506, 4506-B, -B-002 and -B-003 ideally suited for triaxial modal analysis measurements of composite structures that require multiple measurement points, for example, automotive body and power-train measurements, or modal analysis on aircraft, trains and satellites.

USE SCENARIOS

• Structural analysis measurements
• Multichannel modal analysis measurements
• Modal measurements for automotive body and power-train applications

The slots in the accelerometer housing allow easy mounting on five sides using inexpensive plastic clips that fit easily to the test object. The family of CCLD Accelerometers Types 4506 are miniature triaxial piezoelectric accelerometers housed in robust titanium with a single integrated Microtech compatible connector.

Applications	Flight Certified, Industrial
TEDS	NO
TRIAXIAL	NO
Maximum Shock Level (+- peak)	5000g
Resonance frequency	43 KHZ

Minimum order quantity: 1 Piece

HELICOPTER GEARBOX CCLD ACCELEROMETER B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

CCLD Accelerometer is specifically designed for flight-test applications, such as the helicopter gearbox, and delivers reliable measurement in harsh environments.

Type 4511-001 has been specifically designed for Health Usage Monitoring of gearboxes on helicopters, is flight-test certified, and all processes and materials comply with MIL-STD-11268.

The primary design objective has been reliability under extreme conditions yielding very high robustness versus mechanical, electrical and environmental influences.

USE SCENARIOS

• Flight-test applications
• Measurement in harsh environments
• Health Usage Monitoring Systems (HUMS)
• Gearboxes

Operating Temperature Range	-55 to +125 deg C
OUTPUT	CCLD
Freq. range	0.3 - 8000 Hz
WEIGHT	5 g
Maximum Operational Level (peak)	70g
Mounting	stud

Minimum order quantity: 1 Piece

HIGH TEMPERATURE CCLD ACCELEROMETER B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

CCLD Accelerometer designed for continuous high-temperature operation with a stable bias voltage on for instance gas turbine auxiliary equipment. The unit features a top connector, 100 MV/g and 70 g max. operating range.

Types 4526 and 4526-001 feature a built-in CCLD preamplifier designed especially for use with continuous high-temperature operation and with a stable bias voltage.

USE SCENARIOS

• Gas turbine auxiliary equipment
• Power train, engine and exhaust
• Environmental stress screening

CALIBRATION

Type 4526 accelerometer is individually calibrated using state-ofthe-art random FFT (Fast Fourier Transform) technology providing an 1600-point, high-resolution calibration (magnitude and phase). This gives a unique characterisation and secures the integrity of the vibration measurement.

Field checking and system calibration are both made simple by using B&K hand-held Vibration Calibrator Type 4294.

 

Supplied calibration values:

• Sensitivity @ 159.2 Hz
• Maximum transverse sensitivity verification
• Amplitude and phase response (5 Hz to 12.8 kHz)
• Amplitude response with REq-X applied (10 Hz to 12.8 kHz)

UNIGAIN	NO
OUTPUT	CCLD
UNIT	MV
TEDS	YES
TRIAXIAL	YES

Minimum order quantity: 1 Piece

TRIAXIAL CCLD ACCELEROMETER  B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

With a high dynamic range, this triaxial CCLD accelermeter covers a wide range of applications, including on‐road and modal testing.

The family of Triaxial CCLD / IEPE Accelerometer Type 4529 replaces the extremely popular Type 4506 family, using the same flexible mounting accessories to save set-up time and ensure accurate local coordination. Due to their high dynamic range, the accelerometers cover a wide range of applications, including on-road and modal testing. 

To make mounting as flexible as possible, the accelerometer housing has slots to be used in combination with a selection of mounting clips. The clips are attached to the test object with glue or double-sided, adhesive tape. This design allows the accelerometer to be easily fitted to and removed from a number of different objects, for example, during calibration.

USE SCENARIOS

• Multi‐purpose test applications due to a high dynamic range
• Multi‐channel modal and structural analysis measurements
• On‐road vechicle test

Triaxial Accelerometer Type 4529 requires a cable with a 4-pin Microtech connector. Brüel & Kjær can supply cables with connector configurations of two 4-pin Microtech connectors, 4-pin Microtech to 3 × BNC connectors and 4-pin Microtech to 3 × 10–32 UNF connectors for a range of temperatures. For powering two accelerometers from a D-range subconnector, cable AO-0536 is available.

OUTPUT	CCLD
UNIT	MV
TEDS	YES
TRIAXIAL	YES
Applications	MODAL, MINIATURE

Minimum order quantity: 1 Piece

TRIAXIAL CCLD ACCELEROMETER B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

With a high dynamic range, Type 4529-B-001 covers a wide range of applications, including on‐road and modal testing.

The family of Triaxial CCLD Accelerometer Type 4529 replaces the extremely popular Type 4506 family, using the same flexible mounting accessories to save set‐up time and ensure accurate local coordination.

USE SCENARIOS

• Multi‐purpose test applications due to a high dynamic range
• Multi‐channel modal and structural analysis measurements
• On‐road test

Resonance frequency	38KHZ
Applications	General Purpose, Vibration Test
TEDS	YES
TRIAXIAL	NO
Maximum Shock Level (+- peak)	10000G

Minimum order quantity: 1 Piece

GENERAL-PURPOSE CCLD ACCELEROMETER B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are Ariyalur,NagapattinamTirunelveli,Vellore,Sivagangai,Ramanathapuram,Karur,Thiruvarur,Krishnagiri,Theni,Perambalur,Dindigul,Pudukkottai,Tiruvallur

Type 4533-B is a CCLD Accelerometer based on our ThetaShear® design, featuring a low sensitivity to environmental factors, wide frequency range and a TEDS enabled, low-noise preamplifier.

Type 4533-B is a general-purpose CCLD accelerometer with a low-noise preamplifier with built-in TEDS functionality. The accelerometer is part of the Type 4533-B and 4534-B accelerometers, based Brüel & Kjær’s patented ThetaShear® design. 

Both accelerometer types feature a wide frequency range, and have variants with sensitivities from 1 mV/ms–2 to 50 mV/ms–2.

USE SCENARIOS

• General purpose vibration measurement
• Measurements in variable environmental conditions

Each unit features a lightweight, robust, hermetically sealed titanium housing, an insulated base and a 10–32 UNF threaded mounting hole. 

FEATURES

• Insulated base to avoid group loops
• Wide frequency range from 0.2 Hz to 12.8 kHz
• Hermetically sealed to be used in tough environments
• Low noise floor for low-level measurements 
• Low-impedance output to drive long cables

Maximum Shock Level (+- peak)	10000G
UNIT	MV
TEDS	YES
TRIAXIAL	NO
UNIGAIN	NO

Minimum order quantity: 1 Piece

CCLD ACCELEROMETER B&K Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

CCLD Accelerometer designed for wide frequency range, low noise, and low sensitivity to environmental factors.

The general purpose CCLD Accelerometer with TEDS  has a top-mounted coaxial connector, and low-impedance output to drive long cables.

Type 4534-B delivers a wide frequency range from 0.2 Hz to 12.8 kHz, and a low noise floor for low-level measurements. In addition the unit provides low sensitivity to environmental factors, making it ideal for use in changing or tough environments.

 

USE SCENARIO

• General purpose vibration measurement

Each unit features a lightweight, robust, hermetically sealed titanium housing, an insulated base and a 10–32 UNF threaded mounting hole suitable for use in a variety of environmental conditions.

UNIT	MV
TEDS	YES
TRIAXIAL	NO
Maximum Shock Level (+- peak)	1000G
Resonance frequency	38KHZ

Minimum order quantity: 1 Piece

CCLD ACCELEROMETER B&K Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

Designed for wide frequency range, low noise, and low sensitivity to environmental factors.

The general purpose CCLD Accelerometer, Type 4534-B-001, has a wide frequency range, low noise, and low sensitivity to environmental factors. The accelerometer has TEDS.

USE SCENARIO

• General purpose vibration measurement

The accelerometer has a lightweight, robust, hermetically sealed titanium housing, an insulated base and a 10–32 UNF threaded mounting hole suitable for use in a range of environmental conditions.

Type 4534-B-001 has a top-mounted coaxial connector.

UNIT	MV
Applications	VIBRATION TEST
TEDS	YES
Maximum Shock Level (+- peak)	1000G
Resonance frequency	38KHZ

Minimum order quantity: 1 Piece

CCLD ACCELEROMETER B&K

This accelerometer is designed for wide frequency range, low noise, and low sensitivity

Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

Type 4534-B-002 is a general purpose CCLD accelerometer, with TEDS. It has a wide frequency range, low noise, and low sensitivity to environmental factors.

USE SCENARIO

• General purpose vibration measurement

Type 4534-B-002 has a lightweight, robust, hermetically sealed titanium housing, an insulated base and a 10–32 UNF threaded mounting hole suitable for use in a range of environmental conditions. It has a top-mounted coaxial connector

Resonance frequency	130KHZ
Applications	SHOCK
TEDS	NO
UNIT	MV
Maximum Shock Level (+- peak)	80000G

Minimum order quantity: 1 Piece

CCLD SHOCK ACCELEROMETER WITH TOP CONNECTOR B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

Shock Accelerometer for .25 MV/g measurement of very high-level, continuous vibration, mechanical shock and pyroshock.

Types 8339, 8339-001 and 8339-002 are low impedance piezoelectric compression accelerometers intended for measurement of very high-level, continuous vibration, mechanical shock and pyroshock.

USE SCENARIO

• High-level mechanical shock and pyroshock measurements (up to 80,000g)

The output and ground signal are isolated from the mounting surface to prevent ground loops.

Maximum Shock Level (+- peak)	100G
Resonance frequency	7KHZ
UNIT	MV
TEDS	NO
TRIAXIAL	NO

Minimum order quantity: 1 Piece

CCLD SEISMIC ACCELEROMETER WITH TOP CONNECTOR B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are Ariyalur,NagapattinamTirunelveli,Vellore,Sivagangai,Ramanathapuram,Karur,Thiruvarur,Krishnagiri,Theni,Perambalur,Dindigul,Pudukkottai,Tiruvallur

Seismic Accelerometer designed with high sensitivity and ideal for large structures (at very low frequencies), measuring low-level seismic activity.

Type 8340 is a piezoelectric annular shear design accelerometer with integral electronics.

USE SCENARIO

• Seismic measurements

The transducer features a MIL-C-5015, 2-pin top connector, case isolation and a hermetically sealed stainless steel housing to resist outdoor or humid environments.

Type 8340 is mounted by means of a ¼" – 28 UNF tapped hole. A steel stud is supplied with the accelerometer.

unigain	no
output	ccld
unit	mv
teds	no
triaxial	yes

Minimum order quantity: 1 Piece

TRIAXIAL CCLD ACCELEROMETER B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are Ariyalur,NagapattinamTirunelveli,Vellore,Sivagangai,Ramanathapuram,Karur,Thiruvarur,Krishnagiri,Theni,Perambalur,Dindigul,Pudukkottai,Tiruvallur

Designed to operate in harsh environments with a robust 4-pin Glenair® 800-series connector for industrial applications.

Triaxial CCLD Accelerometer Type 8345 is designed to operate in harsh environments.

USE SCENARIOS

• Measurement in harsh environments
• Triaxial measurements
• Permanently installed machine condition monitoring

Its 4-pin Glenair^® 800-series connector is robust for industrial applications. The 3 × M4 holes forming an isosceles triangle on the mounting surface secure the mounting and avoid misalignment of the mounting direction.

USE SCENARIOS	Contact-free detection of reflective objects
brand	B&K
MODEL	PROBE
ANALYZER	VIBRATION
USE SCENARIOS	Synchronisation

Minimum order quantity: 1 Piece

PHOTOELECTRIC PROBE B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are Ariyalur,NagapattinamTirunelveli,Vellore,Sivagangai,Ramanathapuram,Karur,Thiruvarur,Krishnagiri,Theni,Perambalur,Dindigul,Pudukkottai,Tiruvallur

Designed for remote tuning and triggering of vibration measurement and balancing instrumentation in synchronism with rotating or reciprocating machine parts

MM-0024 is ideal for use with the Tracking Filter Type 1623, Vibration Analyzer Type 2515, Portable Balancing Sets Types 3517 and 3537 and Stroboscopes Types 4912 and 4913, all of which include a combined trigger input and power socket which accepts the cable from the MM-0024 directly.

USE SCENARIOS

• Contact-free detection of reflective objects
• Synchronisation of Brüel & Kjær instruments with rotary or reciprocatory machine parts

Supply Voltage	28
TEDS UTID	1025 from serial number 2264319
Max output current (peak)	19
Max output voltage (peak)	7
Polarization voltage support	NO

TYPE 1706

HIGH-TEMPERATURE CCLD PREAMPLIFIER B&K Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

Microphone preamplifier designed to make acoustical measurements at high temperature - up to 125°C (257°F) - with a constant-current line drive (CCLD) input module.

High-temperature CCLD Microphone Preamplifier Type 1706 enables you to make acoustical measurements at temperatures up to 125°C (257°F) with a constant-current line drive (CCLD) input module.

You can connect 1/2″ prepolarized microphones to the preamplifier. The preamplifier’s low output impedance allows problem-free use of long extension cables. The robust, compact design means that you can use Type 1706 over a wide range of environmental conditions.

USER SCENARIOS

• Multichannel signal analysis measurements
• Multichannel sound power measurements
• Industrial machinery noise measurements

FEATURES

• Optimised noise specifications
• ICP^® compatible
• BNC connector for easy installation and use with inexpensive BNC cables
• Connects directly to CCLD sockets and to LEMO sockets with adaptor
• Low output impedance allows long extension cables to be used
• Supports TEDS (Transducer Electronic Data Sheet) and “Smart Transducer Interface” IEEE 1451.4 

USE SCENARIOS	Data acquisition
USE SCENARIOS	real-time analysis
USE SCENARIOS	repetitive testing with B&K Tescia
CHARACTERISTICS	VGA DISPLAY
USE SCENARIOS	General recording and analysis solutions running BK Connect

WB-3620

LAN-XI PERSONAL COMPUTER MODULE B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are Ariyalur,NagapattinamTirunelveli,Vellore,Sivagangai,Ramanathapuram,Karur,Thiruvarur,Krishnagiri,Theni,Perambalur,Dindigul,Pudukkottai,Tiruvallur

A true stand-alone, all-in-one-box measurement solution without sacrificing data quality or reliability.

LAN-XI Personal Computer Module WB-3620-W-001 enables a stand-alone compact measurement system without the need for a traditional desktop or laptop PC for control.

Because this module is, in essence, a PC built into two LAN-XI modules, it interfaces seamlessly with LAN-XI Frames Type 3660-C or Type 3660-D – greatly expanding the capabilities of your existing equipment.

USE SCENARIOS

• General recording and analysis solutions running BK Connect^® software
• Data acquisition, real-time analysis and monitoring for R&D and repetitive testing with B&K Tescia™

CHARACTERISTICS

The module has the following standard interfaces:

• USB 2.0 connectors (x4)
• VGA (Display)
• Minijack (Audio output)
• PoE LAN

CAPABILITIES

LAN-XI Personal Computer Module enables a stand-alone measurement solution on its own or with extended capabilities mounted in LAN-XI Frames Type 3660-C or Type 3660-D. The module can be powered via external power using Mains Adaptor ZG-0426 or, In conjunction with a LAN-XI frame, LAN-XI Battery Module Type 2831 (one or two modules).

This system can act as an independent measurement/recording station, and by connecting to a network (such as long-range Wi-Fi), the computer may be monitored remotely while recording – without relying on the network to transmit all the recorded data.

Additionally, An external, USB-powered touch display can be used for simple in-field monitoring and system management.

Brand	B&K
PACKAGING TYPE	CARTON BOX
MATERIAL	PLASTIC AND RUBBER
color	white
USE SCENARIOS	MEDICAL DEVICE

BK CONNECT TYPE 8493

ACOUSTIC CAMERA APPLET B&K Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

The Acoustic Camera Applet is the software you need to perform noise mapping, noise source identification (NSI) with a hand-held array using beamforming and acoustic holography.

BK Connect® Acoustic Camera Applet is designed to provide a simple measure-and-record solution that acquires data for noise source location applications and creates sound maps of sound intensity and sound pressure overlain with a synchronous video.

The applet comprises all the software functionality needed for noise mapping and NSI in one licence. 

USE SCENARIOS

• Basic array measurements 
• Product noise source location and troubleshooting
• Detection and documentation of buzz, squeak and rattle (BSR) in vehicle cabins
• R&D, quality assurance and troubleshooting for a wide range of industries, such as:
  • Plastics and rubber
  • HVAC
  • Medical devices
  • White goods
• High‐frequency acoustic leak detection 

This set-up uses a hand-held microphone array to create a portable acoustic camera system – a complete kit for real-time noise source identification that needs minimal training to use. 

The combination of a hand-held microphone array and applet enables you to quickly locate sound sources, take screenshots and record video of interesting events and problem areas. Instant playback lets you adjust settings on the fly, ensuring that you record data correctly. 

CHARACTERISTICS

The BK Connect interface and product structure was designed throughout the development process with the users’ roles as a central theme.

BK Connect applets focus on the operator role, providing easy-to-use one-click interfaces to perform specific, and often repetitive, tasks.

CAPABILITIES

• Measure and record audio and video for an event
• Spectrogram yields full overview during measurement and playback
• Display options include graphs of sound pressure, sound intensity and sound power
• Measures over wide frequency range using beamforming and SONAH
• Up‐and‐running in under 20 seconds
• Remote control mode via tablet device

Adding additional channels or the Data Transfer feature requires upgrading to a full BK Connect licence. 

ACOUSTIC CAMERA HARDWARE

This applet requires a standard Brüel & Kjær array and associated LAN-XI hardware, such as BK Connect Acoustic Camera Type 9712-W-FEN. It is ideal for real-time noise source location and mapping and for fast point-and-shoot results and video recordings – in situ and in confined spaces.
 
The kit has the following characteristics:

• A complete system in a weatherproof carry case
• Integrated video camera
• A small, hand‐held design for confined spaces
• Irregular array set-up with a removable backing plate allows both holography and acoustic beamforming in the near or far acoustic field respectively
• Battery life of up to 4 hours

Because it operates in real-time, the acoustic camera is eminently suitable for mapping objects with moving parts and transient events. You can walk and stream video using a hand-held array, or mount an array on a tripod for stationary measurements.

The acoustic camera can measure over a wide frequency range because it uses both acoustic beamforming and statistically optimized near-field holography (SONAH) technologies.

Brand	B&K
CAPABILITIES	Mapping of targets much larger than the array itself
PACKAGING	CARTON BOX
USE SCENARIOS	Troubleshooting during train pass-by measurements
FEATURES	Communicating sound intuitively

TYPE 8608 | PULSE

ACOUSTIC BEAMFORMING SOFTWARE B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

Fast, single-measurement noise source location and mapping of moving and stationary objects, using a microphone array at a distance from the test object.

Acoustic beamforming maps noise sources by differentiating sound levels based on the directions they come from. An array of microphones measures the sound field from a position some distance from the test object. Noise maps display sound strength and directivity as colours emanating from the noise sources. Using the camera mounted on the array, the sound maps can be overlaid images and videos for easy relation to the test object.

Because a beamforming system uses a single‐shot measurement where all channels are measured simultaneously, it is a quick noise source location method that optimizes the use of expensive measuring facilities such as anechoic chambers and wind tunnels, and avoids the repetitiveness of traditional single-probe sound intensity methods.

USE SCENARIOS

• Troubleshooting vehicle interior noise 
• Aeroacoustic noise source location during wind tunnel tests
• Location of noise hotspots on large outdoor machinery 
• Acoustic leak detection on vehicle seals
• Buzz, squeak, and rattle (BSR) detection in vehicle cabins
• Noise source location on moving objects
• Underwater noise source identification (NSI)

With PULSE beamforming software, even small arrays can map large objects. It is possible to map a full vehicle from just one measurement position. And because users can locate the microphone array some distance from the test object, it’s easy to avoid turbulent soundfields such as those found in wind tunnels.

CAPABILITIES 

• Typical use for medium to high frequencies (500 Hz to 20 kHz)
• Measurements at a distance, out of turbulent airflow
• Quick snapshot measurements
• Capturing transient noise events

ADDITIONAL CAPABILITIES

Where the test object is composed of non‐coherent sources, Brüel & Kjær’s refined beamforming algorithm can improve the spatial resolution of the noise maps by a factor of three or more. For noise source location on moving objects, we offer dedicated moving-source beamforming options for road and rail vehicles, aircraft and wind turbines.

For more information on all of the extra options available including transient measurements, sound quality metrics calculations, see Array acoustics options. 

Brand	B&K
FEATURES	tools to support the user
USE SCENARIOS	Import and view data from other BK Connect sources
PACKAGING	CARTON BOX
ADDITIONAL CAPABILITIES	Scratchpad Calculator

BK CONNECT TYPE 8400

DATA VIEWER B&K Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

An easy-to-use, standalone tool for managing and viewing data and creating reports: the tasks where sound and vibration engineers typically spend a majority of their time. BK Connect® Data Viewer is part of the core framework of the BK Connect software platform.

BK Connect Data Viewer is a free application that provides a user-focused structure. It gives a streamlined workflow for comparing results from either the internal database or loaded from an external file, and the tools to generate your final report.

This application is the basic framework for all BK Connect applications (except for BK Connect Hardware Setup) and provides the tools to support the user throughout the data analysis process. The application comprises the project browser for managing data (including import and export), data display elements for viewing and analyzing data, and all the tools needed for creating reports using default templates, templates based on existing reports or customized templates for new or ad hoc scenarios. 

Request your free license

USE SCENARIOS

In the course of validating or post-processing data and creating reports:

• Import and view data from other BK Connect sources (To import data from other sources like PULSE Reflex and PULSE LabShop or third-party-based software, or to work with legacy data and shared projects, BK Connect File Importers/Exporters are needed).
• Centrally organize data from multiple tests, facilitating sharing and comparison 
• Find and copy data from one project to another via the project browser or from the BK Connect database using the search tool
• Add metadata to projects for context and for data management in the database
• Create reports for ad hoc measurements or as an automated process

ADDITIONAL CAPABILITIES

BK Connect Type 8400-A advanced license
The addition of this license enables the following capabilities:

• Scratchpad Calculator
  The Scratchpad Calculator enables standard mathematical and statistical operations for 2D and 3D functions and includes the capabilities for basic reporting
• Data Table Viewer
  The Data Table Viewer provides a table framework for reviewing data and creating automated reports.
• Result Matrix Viewer
  The Result Matrix provides a structured overview of data that simplifies the selection and comparison of results when managing data from multiple tests

The Data Table Viewer and Results Matrix Viewer allow the creation of custom display rules making repeatable and fast comparisons part of the natural workflow.  These rules can be exported for sharing with others in the organization so everyone reviews data in the same way, making decisions clearer.

BK Connect Team Server Search Type 8400-T-F
This powerful data management option allows you to designate a group who can share data and processed results to the BK Connect Team Server. The uploaded data is the searchable using automatically assigned and user-definable metadata for download to local projects.

PREREQUISITE

BK Connect Data Viewer Type 8400 is a prerequisite for all other BK Connect applications except for BK Connect Hardware Setup Type 8401

Brand	B&K
Software platform	PC
USE SCENARIOS	Identifying gear noise in low-friction gearboxes
PACKAGING	CARTON BOX
CAPABILITIES	Statistical analysis of cycle-related phenomena

TYPE 8440 | BK CONNECT

ANGLE DOMAIN ANALYSIS SOFTWARE B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are Ariyalur,NagapattinamTirunelveli,Vellore,Sivagangai,Ramanathapuram,Karur,Thiruvarur,Krishnagiri,Theni,Perambalur,Dindigul,Pudukkottai,Tiruvallur

Angle domain analysis software designed for analyzing sound and vibration signals in relation to the cycles of rotating components such as engine crank shafts.

This application takes recorded time data and resamples it so that it can be presented as a function of the rotation angle during the duty cycle of rotating machines, such as car engines. By relating sound and vibration data to the angle of the engine’s crankshaft or flywheel, it is easy to see correlation with the position in the engine’s cycle. This new perspective gives insights into noises that arise from cyclic phenomena, such as the firing of a particular cylinder, or vibrations from a certain point in the engine’s duty cycle. 

USE SCENARIOS

• Analysis of power train sound and vibration in relation to crankshaft angle for noise, vibration and harshness (NVH) engineering
• Identifying gear noise in low-friction gearboxes
• Reducing noise from imbalance in two- and three-cylinder engines
• Comparison of angle-domain data sets from different test runs

This angle-domain processing software works with any signal, or combination of signals, that gives the duty cycle period. This can be a tacho pulse signal from a shaft encoder or a magnetic pickup on a flywheel, or a top dead-centre (TDC) signal from a flywheel or test-bed encoder, or from an engine control unit. 

By resampling raw time-data from the time domain so that it corresponds directly to the position of a rotating component, it gives automatic and unequivocal identification of where sound and vibration events occur in an engine’s cycle – instead of corresponding only to the time intervals at which the data was originally measured. For example, during crank-angle analysis on a 4-stroke engine, the data is sampled in relation to the 720° (two complete revolutions) that comprise a complete duty cycle.

CAPABILITIES

• Statistical analysis of cycle-related phenomena
• Cycle statistics:  minimum, maximum, mean, RMS and peak-peak values per cycle, vs time or RPM
• Contour, waterfall and Campbell plots of cycle history vs time or RPM
• 3D displays of cycle vs time or cycle number
• 2D displays of cycles (either overlaid or single)
• Gated statistics vs cycle number
• Duty cycle extraction with fixed-angle increments
• Ability to apply offset for TDC correction based on TDC signal or missing pulses (tacho repair)
• Integrated Microsoft^® Office reporting capabilities

Combining this application with BK Connect® Time Data Recorder Type 8402 makes Time Data Recorder tasks available within the Angle Domain Analysis application.

REQUIREMENTS

This application requires BK Connect® Data Viewer Type 8400. Type 8400 is free. 

Brand	B&K
CAPABILITIES	Low to medium frequencies
USE SCENARIOS	Analyzing acoustic leaks in door seals
FEATURES	Capturing transient noise events in detail
PACKAGING	CARTON BOX

TYPE 8607

ACOUSTIC HOLOGRAPHY SOFTWARE b&k Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

Calculates color-coded sound maps on any plane parallel to the measurement plane. This uses any property of the sound-field such as sound pressure, sound intensity or particle velocity. Maintains source-separation capabilities at low frequencies.

An acoustic holography system creates highly accurate sound maps using measurements made at multiple points next to the object. These use a hand-held microphone array, a fixed array, or a robot-controlled microphone array. With this method, many measurement points can be acquired simultaneously – saving time compared to traditional sound intensity methods. 

The resulting maps show sound levels as colours emanating from the object’s sources. These sound maps can be laid over images and videos for easy relation to the test object. The software allows any relevant property of the soundfield to be calculated, such as source strength and directivity. Conformal noise mapping options allow measurements that follow the shape of the object, and using a set of patch measurements, you can then create animated, 3D noise maps on a 3D model of the object. Users can also listen to individual points during transient events. 

USE SCENARIOS

• Detailed noise mapping of vehicle components such as engines and powertrains
• Mapping overall product noise for white goods, office machinery, and heavy machinery
• Analyzing acoustic leaks in door seals
• Automated, robotic measurement processes with a limited array size
• Capturing transient noise events in detail 

Brüel & Kjær’s patented holography algorithm SONAH (statistically optimized nearfield acoustic holography) improves resolution over conventional NAH (near-field acoustic holography), and allows accurate mapping of objects with smaller microphone arrays that don’t cover the whole measurement object at one time. It also allows more arrays that are not rectangular, which gives more flexible array options such as combined arrays that also allow beamforming capabilities for higher frequencies and moving sources. 

CAPABILITIES

• Low to medium frequencies (100 Hz – 2kHz)
• Mapping of sound pressure, sound intensity, particle velocity and sound quality metrics
• Noise sub-source sound power contribution analysis
• Analyzing transient events, averaging in time, RPM, and angle domains
• Conformal mapping where sound maps follow the object’s shape
• Intuitive documentation including animations using source-image overlay
• Spatial transformation of sound fields (STSF)

ADDITIONAL CAPABILITIES

• With the addition of Brüel & Kjær’s wideband holography option, you can extend the frequency range limit, allowing good sound power estimates over a wide frequency range from one measurement – instead of needing a separate beamforming measurement for higher frequencies
• A proximal holography option (BZ-5963) makes conformal maps that follow the shape of the object under test, in one measurement, using our equivalent source method (ESM). As all the signals are obtained simultaneously, transient calculations can be performed to create the 3D noise map
• A robot positioning system (BZ-5370) assures test repeatability with fully automatic measurements

 

Model Name/Number	ATH-288
Accuracy	70
Usage/Application	Household
Display Type	Digital
Material	Plastic
Power Source	1.5V

Minimum order quantity: 1 Piece

Big Display Indoor-Outdoor Thermo / Hygrometer with Clock large 3 line LCD display.

• Environment Comfort Display :COMFORT, WET, DRY
• Temperature Range :(IN/OUT)-50˚C ~70˚C (-58˚F ~ 158˚F)
• Temperature Accuracy : ±1.0˚C or ±1.8˚F
• Humidity Range : (10% ~ 99%)
• Humidity Accuracy : ±5% (35% ~ 75%) or else ±10%
• Time / Temperature / Humidity indicate
• Temperature Reading for ˚F &˚C
• MAX./MIN. Temperature & Humidity
• 12/24 hours system clock.
• Sensor Length : 3 Meters.
• Power : AAA 1.5V X 1

Number of measured harmonics	7, allows for full viscoelastic modeling
Minimum sample volume, flow mode	50
Maximum time resolution	100 data points per second
Computer requirements	PC with 64-bit Windows 7 SP1, 8, 8.1 or 10,At least 4 GB RAM
Measurement channels	8
Working temperature	4 to 70 DegreeC, 4 to 150 DegreeC using accessory chamber

Minimum order quantity: 1 Piece

QSense Pro:Do you need to perform large-scale QCM-D analysis? The fully automated QSense Pro is best fit for the job

 Most suitable when:

• You need maximized throughput
  The 8-channel system can produce a lot of data every day
• You want to test and compare samples
  8 channels and 4 separately controlled syringe pumps let you evaluate several samples and parameters in one go
• You need highly reproducible results
  The fully automated system minimizes human errors and maximizes user-independence
• You want to conduct experiments in both high and low temperatures
  The instrument works with a temperature range between 4-70 °C
• You need more time
  The system can be pre-programmed and left unattended during experiments, leaving you with time to do other things

Specification:

Measurement range and capacity
Sample and fluidics 

Performance characteristics 
Dfind features:

• A complete analysis toolbox 
• Intuitive interface 
• Guided modelling
• Material library
• Autoplotting
• Smart tools
  
• Analyze all data in one go

Computer requirements	PC with 64-bit Windows 7 SP1, 8, 8.1 or 10 ,At least 1366x768 px screen resolution
Measurement channels	4
Working temperature	15 to 65 DegreeC, 4 to 150 DegreeC using accessory chamber
Sensors	5 MHz
Number of measured harmonics	7, allows for full viscoelastic modeling
Maximum time resolution	300 datapoints per second
Minimum noise	Frequency: 0.03 Hz

QSense Analyzer:Both fast and flexible, QSense Analyzer enables you to compare several samples at the same time. 

 Most suitable when:

• You are interested in high throughput
  The system has 4 channels for simultaneous measurements making it an excellent choice for rapid data collection
• You want to test and compare samples
  Running several samples at the same time lets you evaluate different parameters in one go
• You want to study a broad range of scenarios
  QSense Analyzer supports a temperature range between 15-65 °C and the possibility to use harsh chemical solvents
• You need the possibility to expand your experimental setup
  Add accessory chambers and modules to explore more experimental opportunities, extended measurement conditions, or combination with complementary techniques

Specification: 

Measurement range and capacity Sample and fluidics  Performance characteristics 

 

 Dfind features:

• A complete analysis toolbox 
• Intuitive interface 
• Guided modelling
• Material library
• Autoplotting
• Smart tools
• Analyze all data in one go

Brand	Biolin scientific
Shape	Rectangular
Color	Grey
Measurement channels	1
Working temperature	20 to 45 DegreeC
Sensors	5 MHz
Number of measured harmonics	2
Maximum time resolution	4 datapoints per second

Minimum order quantity: 1 Piece

QSense Initiator:Get started with QCM-D technology using QSense Initiator. The instrument features core functions and produces high quality data. 

 Most suitable when:

• You are getting started with QCM-D
  A clean design and straightforward software makes QSense Initiator perfect as an introduction with the QCM-D technology
• You are into the basics
  QSense Initiator supports all the core functions and basic qualities of QSense instruments.
• You need to study interactions qualitatively
  But not to quantify your films.
• You will experiment within a limited temperature range
  You are performing your measurements between 20-45 °C.

 

Specification:

Measurement range and capacity Sample and fluidics  Performance characteristics 

 Computer requirements:

REQUIRED

• PC with 64-bit Windows 7 SP1, 8, 8.1 or 10
• At least 1366×768 px screen resolution
• At least 4 GB RAM
  
  
  

RECOMMENDED:

• 1920×1080 Full HD screen resolution.
• At least 8 GB RAM
• At least 50 GB HD space

Core i5 5th generation Intel (or comparable) processor or better

brand name	B&K
model name	PHOTOELECTRIC PROBE
features	provides a very convenient transducer for triggering a portable stroboscope
packaging type	carton box
color	black

Minimum order quantity: 1 Piece

PHOTOELECTRIC PROBE B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

The Photoelectric Tachometer Probe provides a very convenient transducer for triggering a portable stroboscope, such as Type 4912 where the range of motion is great enough,i.e., more than a few millimetres. 

The Photoelectric Probe is designed for use with Data Collector Type 2526, Multichannel Analysis System 3550, Multichannel Data Acquisition System Type 355, Signal Analyzer Unit Type 2035, Generator and Sampling Module Type 3106 and Stroboscope Type 4912 - either in synchronism with rotating - or reciprocating machine parts.

These instruments are provided with a combined trigger input and power supply socket which accepts the cable from the MM-0012 directly.

USE SCENARIOS

• Synchronizing various Brüel & Kjær instruments with rotary or reciprocatory motion
• Reflective object detection
• Displacement detection

Operating temperature range short-tem	-30 to +80
Capacitance with integral cable	7500
Weight including integral cable	1.6 kg (3.5 lb)
Dimensions	93 mm (3.66 inch)
Max operating static pressure	260 dB = 9.8 x 10^6 Pa

TYPE 8105

SPHERICAL HYDROPHONE B&K

Spherical hydrophone with rugged construction capable of withstanding pressures of up to 9.8 MPa (100 atm; 1000 m (3250 ft) ocean depth) and featuring exceptional directional characteristics.

Type 8105 is a robust spherical hydrophone usable down to 1000 m ocean depth with excellent directional characteristics.

USE SCENARIOS

• Calibration reference standards 
• Ultrasonic measurements in liquids 
• Cavitation measurements 
• Laboratory and industrial measurements in liquids and gases 
• As underwater projectors (8103, 8104 and 8105) 
• Noise measurements in humid and polluted atmospheres

A small, spherical transducer for making absolute sound measurements over the frequency range 0.1Hz to 160 kHz with a receiving sensitivity of −205 dB re 1V/μPa. It is rugged, being capable of withstanding pressures of up to 107 Pa (100 atm.; 1000 m (3250 ft.) ocean depth).

This hydrophone has excellent directional characteristics: at 100 kHz, it is omnidirectional over 360° in the x-y (radial) plane and 270° in the x-z (axial) plane.

Operating temperature range short-tem continuous	-30 to +60 C
Charge sensitivity	n/a
Weight including integral cable	382 g (0.84 lb)
Dimensions	182 mm (7.17 inch)
Max operating static pressure	260 dB = 9.8 x 10^6 Pa

LOW-NOISE HYDROPHONE WITH PREAMPLIFIER B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

Hydrophone Type 8106 features a built-in, thick-film, and low noise, 10 dB preamplifier, delivering signal conditioning for transmission over very long distances. This makes Hydrophone Type 8106 suitable for underwater sound measurements down to 1000 meters depth. 

Type 8106 is a wide-range, piezoelectric hydrophone with preamplifier for making absolute sound measurements over the frequency range 7Hz to 80 kHz, featuring an impressive receiving sensitivity of −173dB re 1V/μPa.

USE SCENARIOS

• Calibration reference standards 
• Ultrasonic measurements in liquids 
• Cavitation measurements 
• Laboratory and industrial measurements in liquids and gases 
• As underwater projectors (8103, 8104 and 8105)
• Noise measurements in humid and polluted atmospheres

The preamplifier provides a 7Hz high-pass filter and an insert-voltage calibration facility, but does not allow the hydrophone to be used as a projector. 

The hydrophone is built to withstanding high static pressure, the operational upper limit being 107 Pa (100 atm / 1000 m (3250 ft.) ocean depth. 

An integrated watertight connector allows quick disconnection of the cable and makes replacement and storage very easy.

Operating temperature range short-tem	-30 to +80
Integral cable	6 m waterproof low-noise double-shielded
Weight including integral cable	170 g (0.37 lb)
Dimensions	50 mm (1.97 inch)
Max operating static pressure	252 dB = 4 x 10^6 Pa

TYPE 8103

MINIATURE HYDROPHONE B&K Importers Distributors,Dealers ofBRUEL&KJAER suppliers are tirupur,thiruvannamalai,Nilgiris,Villupuram,Virudunagar,Erode,Madurai,Thanjavur,Tiruchirappalli,Kanchipuram,Dharmapuri,Salem,Cuddalore

Miniature Hydrophone Type 8103 is a small piezoelectric transducer designed for high-frequency laboratory and industrial use. The instrument is particularly useful in the acoustic study of marine animals or for cavitation measurement.

Miniature Hydrophone Type 8103 is designed for high-frequency laboratory and industrial use and is supplied with an integral 6m cable terminated 10-32 unf microdot plug.

USE SCENARIOS

• Calibration reference standards 
• Ultrasonic measurements in liquids 
• Cavitation measurements 
• Laboratory/industrial measurements in liquids and gases 
• As underwater projectors (8103, 8104, and 8105) 
• Noise measurements in humid and polluted atmospheres

Miniature hydrophone Type 8103 is a small, high-sensitivity hydrophone for absolute sound measurements over the frequency range 0.1Hz to 180 kHz, with a receiving sensitivity of −211 dB re 1V/μPa. The high sensitivity and good all-round characteristics, make it ideal for laboratory, industrial, and educational use.

The high-frequency response of this hydrophone becomes especially valuable when making acoustic investigations of marine animals, and for measuring pressure-distribution patterns in ultrasonic-cleaning baths. 

Packaging Type	carton box
Usage/Application	3-point measurement
Model Name/Number	L107P3
Color	black
Weight	250 g
Easy Handling	Yes
Brand	Kroeplin
Storage Temperature	-10 - 50 DegreeC
Protection Class	IP67

Minimum order quantity: 1 Piece

Kroeplin - L107P3:

Electronic three-point measuring device

Measuring range Meb: .28 – .55 inch

Digit step value Zw: .00005 / .0001 / .0002 / .0005 / .001 / .002 inch

Max. probe arm length L: 1.34 inch

Product features

 

Brand	B&K
PACKAGING	CARTON BOX
TYPE	BK CONNECT TYPE 8441 PASS-BY VIEWER B&K
CAPABILITIES	Results can be viewed during the test
FEATURES	Collaborative working across the organization or multiple companies

BK CONNECT TYPE 8441

PASS-BY VIEWER B&K Importers Distributors,Dealers of BRUEL&KJAER suppliers are Chennai,Chegalpattu,kallakurichi,kanchipuram,mayiladurai,kanyakumari,Coimbatore,Namakkal,Ranipet,Tenkasi,thootukudi,Thirupattur

BK Connect® Pass-by Viewer for easy inspection of results during the test and post process.

The BK Connect Pass-by Viewer is tailored specifically for the presentation of pass-by data whether from indoor testing or outdoor testing and works directly with stored data files in the HBK Team Server. With Team Server automatically integrated into the Pass-by Viewer interface, results can be effortlessly inspected by any tester or engineer with access to the shared file repository – including those working remotely from the test facility. 

USE SCENARIOS

• Presentation of pass-by noise data from indoor and outdoor testing to allow for easy inspection of results 
• Collaborative working across the organization or multiple companies
• Tailored data searches based on metadata enabling multiple sets of data to be viewed and compared 

CAPABILITIES

• Results can be viewed during the test 
• Data files are stored in a central shared file repository that is accessible using standard Windows® profiles
• File repository is either local on the measurement PC or in a shared folder on the network, which enables collaborative working across the organization 
• The Pass-by Viewer user interface presents a table of overall pass-by results from which any selected cell enables graphical presentation of the relevant SPL curves and 3rd-octave spectra. 
• At any time, an Excel® report can be made of the results in the table. 

Brand	aimil
Model Name/Number	Electronic Bowie Dick Sensor
Usage/Application	Industrial
packaging type	carton box
application	Bowie Dick Test
Country of Origin	Made in India

Minimum order quantity: 1 Piece

Aimil-Electronic Bowie Dick Sensor:

This highly compact Bowie Dick Sensor is the only electronic test device on the market designed for 121 °C processes – and, when necessary, 134 °C. The sensor provides far more insight into critical sterilization parameters than previously possible, making it a critical tool for any steam penetration study.Unlike traditional chemical indicators, where you subjectively decide according to a change in color, this device provides you with an accurate report that eliminates any guess work.The device is extremely easy to use and requires little to no training. With just a single click in the software, the unit will start to measure and record data. Once the Bowie Dick Test Program is done, the device is simply placed back in the reader station where the software automatically processes the data and provides a test result – simple and easy!

Application:

Bowie Dick Test

Brand	aimil
Usage/Application	Industrial
Model Name/Number	-Microbial Monitor BioCapt Single-Use
Color	white
application	Facility monitoring system for clean areas
Country of Origin	Made in India

Minimum order quantity: 1 Piece

Aimil-Microbial Monitor BioCapt Single-Use:
A replacement for settle plates, the BioCapt® Single-Use Cleanroom Microbial Monitor by Particle Measuring Systems (PMS) helps minimize false positives for microbial activity in pharmaceutical cleanrooms by reducing contamination from handling of agar settle plates. This results in a decrease in investigations while increasing productivity. Additionally, many costly and time-consuming sterilization steps, such as autoclaving, disinfecting, handling and logistics are eliminated. This innovative approach to viable microbial air sampling and monitoring builds on the collection efficiencies of the BioCapt stainless steel viable impactor, while also virtually eliminating false positives through specialized packaging and single-use application.The BioCapt Microbial Impactor (Single-Use) achieves sampling with minimal air disruption and can be used to sample efficiently at 25 or 50 L/min to suit both routine monitoring and fast sampling needs. This new device has a proven recovery of microorganisms under stressed conditions after two hours of continuous air sampling (25 L/min flow rate) reducing the number of plate changes required for continuous air sampling. Learn more about this continuous air sampling solution.
Application:Facility monitoring system for clean areas

Color	silver
Model Name/Number	WEARSCANNER
I Deal In	New Only
Temperature range	-20 DegreeC - 80 DegreeC
Packaging Details	carton box
Particles	Ferritic or non-ferritic
Flow velocity	0.01m/s - 5m/s (0.1 - 40 l/min)
Oil type	Mineral, synthetic or biodegradable

Minimum order quantity: 1 Piece

Aimil-WEARSCANNER:

WEARSCANNER detects electrically conductive particles in oil using a patented method based on the eddy current principle. Results are independent of oil temperature, flow rate, viscosity, air and water contents or oil color (darkening). The particles are counted real-time and classified according to their size. Minimum particle detection size is down to 50µm to ensure the detection of the slightest start of detrimental and abnormal wear.

 
Online Particle Counter Monitors Wear Debris in Oil 

This is an Online Particle Size Distribution Counter Monitors Wear Debris in Oil that helps in following ways:

1. Avoids consequential damage
2. Enhances the availability of the plant
3. Switching output for alarms
4. Recognizes bearing & gear teeth damage

Recognize damage before they totally fail to operate. Use’ Wear Scanner’.

 

See how WEARSCANNER® works: 

• Each peak represents a particle that flows through the sensor tube.
• The amplitude indicates the size of the particle.
• The peaks are counted in set time intervals
  • And the number of peaks per time interval is transmitted via Modbus TCP.
• The size categories – three in this case – are configured for each particular situation.
• The time resolution and scan rate can be selected. 

The sensitivity of the WEARSCANNER® can be adapted by adjusting the gain, power and filter to the machine application.

General rule: As you know, if large will be the particle that occurs more damage.

 

Technical details:

Fitting dimensions

1/2“- other sizes available upon request

 

Measuring method

Eddy current, differential coil principle

 

Particles

Ferritic or non-ferritic

 

Particle size class

Up to 8 size classes can be set

 

Flow velocity

0.01m/s – 5m/s (0.1 - 40 l/min)

 

Oil type

Mineral, synthetic or biodegradable

 

Oil pressure

Max. 16bar

 

Temperature range

-20°C – 80°C

 

Signal processing

Particle distribution counters with integral. Average determination and classification.

 

Application:

Online wear particle monitoring system.

Color	grey
Usage/Application	Vibration measurement and support for vibration analysis
model name	Wilcoxon Accelerometers
Packaging Details	carton box
Country of Origin	Made in India

Minimum order quantity: 1 Piece

Aimil-Wilcoxon Accelerometers:

Accelerometers sense vibration commonly found in most industrial machinery. Maintenance professionals use accelerometers for predictive maintenance to lower overall cost and increase machinery performance. Wilcoxon Research® sensors are used to monitor a variety of machinery including: motors, fans, pumps, gearboxes, blowers, machine tool spindles, compressors, chillers, rollers, and mixers.

Application:

Vibration measurement and support for vibration analysis

model name	GBSAR Ground Based SAR G2000
brand	Aimil
applications	Slope Monitoring of Dump and Highwall in Open Cast Mines, Landslide Monitoring, Structure Monitoring
features	It is highly easy to use & deploy, and continuously monitored under all weather conditions.
color	grey
product type	scanner

Minimum order quantity: 1 Piece

Aimil- GBSAR Ground Based SAR G2000:

The GBSAR 2000 is useful for surface deformation monitoring in real-time. It is highly easy to use & deploy, and continuously monitored under all weather conditions. This radar system is appropriate for disaster monitoring, risk assessment, and establishing an early warning framework for hazard management.The GBSAR 2000 can monitor the surface deformation of earth environments (such as landslides, terrain subsidence, falling rocks, glaciers, avalanches, volcanoes, etc.) & man-made structures (such as bridges, buildings, towers, dams, roads, etc.)

Application:

Slope Monitoring of Dump and Highwall in Open Cast Mines, Landslide Monitoring, Structure Monitoring

color	black
product type	scanner
application	Volumetric Measurement, Slope Monitoring in Under Ground mines, Void Measurement
brand	aimil
model name	Maptek SR3mkII

Minimum order quantity: 1 Piece

Aimil-Maptek SR3mkII:

Maptek SR3mkII laser scanner is a new short-range laser scanner designed for underground survey and mapping applications. It combines fast accurate sensing, dedicated mount accessories, and powerful modeling software for improving overall productivity and safety underground.

Application:

Volumetric Measurement, Slope Monitoring in Under Ground mines, Void Measurement

application	Volumetric Measurement, Slope Monitoring of Waste Dump and Highwall in mines
features	long-range survey system combining fast accurate sensing, high-resolution digital imagery, software
brand	aimil
model name	Maptek XR3mkII
color	black

Minimum order quantity: 1 Piece

Aimil-Maptek XR3mkII:

Maptek XR3mkII laser scanner is an extra long-range survey system combining fast accurate sensing, high-resolution digital imagery and powerful modelling software for improving overall productivity and site safety. The system includes a new, improved high dynamic range panoramic camera for better digital panoramic imagery. This produces high-resolution images for geotechnical analysis and high impact visualization.The Maptek XR3mkII laser scanner possesses the hallmark automated mine survey workflow favored by surveyors, geotechnical engineers, geologists and mining engineers. Matched with dedicated software it generates accurate survey deliverables for mining, civil, and infrastructure applications.

Application:

Volumetric Measurement, Slope Monitoring of Waste Dump and Highwall in mines

uses	7020 Power Sensor is an economical plug and play solution for power measurement needs.
brand	Aimil
model name	7020 Power Sensor
Application	Analog Cellular, Digital Cellular, 3G, 4G, Tetra, APCO/P25, Trunking, CDMA, TDMA, WCDMA, GSM
color	black

Minimum order quantity: 1 Piece

Aimil- 7020 Power Sensor:

7020 Power Sensor is an economical plug and play solution for power measurement needs. The 7020 determines and reports Forward and Reflected True Average Power and VSWR over a wide frequency range of 350 MHz to 4.0 GHz. It also never requires field calibration, only requires factory calibration once per year, and is traceable to National Institute of Standards and Technology (NIST).

Application:

7020 has following Applications WPS measures: Analog Cellular, Digital Cellular, 3G, 4G, Tetra, APCO/P25, Trunking, CDMA, TDMA, WCDMA, GSM, Transportation, Tactical Military, Radar, Avionics, Marine, LMR, Analog Broadcast, Digital Broadcast, GSM, GPRS, EDGE, UMTS, HSDPA, Bluetooth, Fire, GPS, NPSPAC, Paging, Project 25, Public Safety, Telematics, Utilities, WIMAX and WLAN. Measurements performed: Forward and Reflected Calculations Performed: VSWR and True Average Power

model name	RF Power Sensors
application	Precision Semi-Conductor Applications
uses	Designed to provide ease of use and reliable data for development and production engineers
color	black
brand	aimil

Minimum order quantity: 1 Piece

Aimil-RF Power Sensors:

RF Power Sensors bring stunning and traceable accuracy to laboratory and semiconductor fab environments. Designed to provide ease of use and reliable data for development and production engineers. At calibrated frequencies, these sensors are capable of 0.5% (7037 Series) or 1% (7027 Series) accuracy for measurements of the gated power within a RF pulsed waveform. Calibration is traceable to the National Institute of Standards and Technology (NIST) so you can be confident in the quality and accuracy of the measurements these sensors provide.

Application:

Precision Semi-Conductor Applications